[0x00]

Right, I've installed 3CX in a new environment. All SIP providers are registered and all internal soft/hard phones work. I can make incoming & outgoing calls no problem.

I can't however get external soft phones to work. I can see from the debug log it says it's connected, then ended by the server.

Do I have to open & forward 9000 > 9049 to get this working? I thought the 3CX Tunnel would negate the need for this.

Also, apart from the Event and System logs, is there a real time log I can see each connection coming in as?

All help gratefully received!

[leejor]

I have to assume that you are running the tunnel option on the remote 3CX phones, if so then only port 5090 is used. What does the 3CX log show for a call attempt?

[0x00]

Hi there, thanks for the help.

This is what I see on the 3CX Soft phone debug view. Using an online port scanner I can see that 5060 and 5090 show as open.

EDIT: Is there a Tunnel log server side I can view?

Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel send from phone to PBX: REGISTER
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel send from phone to PBX: REGISTER
Tunnel has been disconnected by remote end
Tunnel is attempting to connect remote tunnel 123456 [xxx.xxx.xxx.xxx:5090]
Tunnel connection established
Tunnel has been disconnected by remote end
************ debug paused ***********************

[leejor]

EDIT: Is there a Tunnel log server side I can view?

There is a log in the 3CX PBX, that is the one you should be looking at as it may give a clue as to why the registration attempt is being dropped. If there is nothing in there, then the requests are not getting past your router.

I assume that you set up the Tunnel password.

[0x00]

Is that the Server Activity Log in 3CX admin, above the Server Event Log? Or do I need to be looking somewhere else?

[0x00]

OK, feel rather stupid, but I got there thats the main thing.

I noticed the "Disalow use of extension outside the LAN".

Putting the logging mode to verbose enabled me to see that WAN requests were blocked, quick google and a thread on here put me in the right direction.

Many thanks for you help lee

[eagle2]

For registering external extensions via 3CX tunnel you DON'T need to enable outside of LAN registrations in extension settings (as well as if you are using VPN / VLAN). In your case this most probably means you are not configuring correctly remote extensions / tunnel.

Regards