Auto Provision your Htek UC9 series IP Phone for 3CX v15
pixel500w-500x1
Zero Admin
With the new Dashboard
pixel500w-500x1
Bulletproof Security
With SSL certs and NGINX
pixel500w-500x1
Install on $150 Appliance
Intel MiniPC architecture
pixel500w-500x1
New, Intuitive Windows Client
More themes, more UC
pixel500w-500x1
More CRM Integrations
Scripting Interface to add your own
pixel500w-500x1
Improved Integrated Web Conferencing
iOS and Android apps included
pixel500w-500x1
Personal Click2Meet URLs

How to configure Htek UC9 Series for 3CX

How to configure Htek UC9 Series for 3CX

htek-phones-guide (2).jpg

This guide applies to v15 only.

On this topic

How to configure Htek UC9 Series for 3CX

Supported Models: Htek UC series

Step 1: Upgrade to Minimum required firmware

Step 2: Factory Reset the IP Phone

Step 3: Provision the phone

Local LAN or SBC: Provision via Plug’n’Play

Remote phones: Provision via RPS server

Important note about BLF Layout

Known Limitations

Supported Models: Htek UC series

  • Htek UC902  - min. firmware version 2.0.3.99
  • Htek UC924  - min. firmware version 2.0.3.99
  • Htek UC926  - min. firmware version 2.0.3.99

Step 1: Upgrade to Minimum required firmware

Check that the phone is running the minimum firmware described above. Read how to check what firmware the phones are running and how to upgrade them in this guide: How to manual upgrade Htek UC series  phones.

Step 2: Factory Reset the IP Phone

Before provisioning the IP phone, the phone must be brought back to factory defaults in case the device has residual settings of a previous configuration. To reset the device read our How to factory reset Htek UC series phones document.

Step 3: Provision the phone

There are several methods to provision a phone:

  • Plug n Play -  For phones on the local LAN or behind the 3CX SBC.
  • RPS - For phones on remote networks that will connect directly to 3CX and use STUN.

For more information, see When can I use which provisioning method?

Local LAN or SBC: Provision via Plug’n’Play

  1. Connect the phone to the network. A PNP request will be sent automatically to 3CX.
  2. Go to the 3CX Management Console ⇒ “Phones” page. The new phone will be marked in Bold.

  1. Click on the BOLD entry and choose between “Assign Ext” or “Add Ext”, depending on whether you want to assign the phone to an existing extension or create a new one.

  1. All major provisioning settings are pre-populated. If your 3CX has multiple network cards, select to which network this IP phone is connected.
  2. Click “OK”. The phone will take the configuration on the fly and may reboot to finalize the setup.

Remote phones: Provision via RPS server

  1. Take note of the phone’s MAC address, usually written at the back.
  2. Navigate to the 3CX Management Console  “Phones” and press “+ Add Phone”.
  3. From the dropdown list select the extension to which this phone must be assigned.
  4. In the next dialog select the Vendor/Model of the phone and enter the device’s MAC address.

  1. Switch the “Provisioning Method” to “Direct SIP (Stun - Remote)” and click “OK”.

  1. You can make sure that the extension is ready to be configured via RPS by checking the “Event Log” from the dashboard:

If the message comes up in an “Warning” follow the instructions outlined in the message and use the Manual Link Provisioning method outlined here.

  1. The phone is now ready to be provisioned - you can boot up the phone anywhere in the world connected to the internet.
  2. The phone will prompt for username and password: Enter the extension number as username and the voicemail pin as the password.

Note: Ensure that the input mode is set to digits (green box).

Important note about BLF Layout

All devices featuring BLF keys next to the LCD are used as Line Keys. All BLF keys on the right hand side panel can be configured freely.

Known Limitations

  • Currently no known limitations.

You might also be interested in:

<