• V20: 3CX Re-engineered. Get V20 for increased security, better call management, a new admin console and Windows softphone. Learn More.

3CX and Cisco Router

Status
Not open for further replies.

Stormblue

Joined
May 9, 2011
Messages
2
Reaction score
0
Hi everyone,
We are trying to get our brand new 3CX up and running. Right now, we have a problem with the setup of our Cisco 2811 router with the E1-Card inside.
Does anyone have a config example, how to setup the Cisco box to talk to the 3CX?

Here's the error from the 3CX log:
*****snip*****
20:15:31.344 [CM500002]: Unidentified incoming call. Review INVITE and adjust source identification:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.60.1:5060;branch=z9hG4bKFA898;x-route-tag="tgrp:xxx"
Max-Forwards: 70
Contact: <sip:[email protected]:5060>
To: <sip:[email protected]>
From: <sip:[email protected]>;tag=27001210-10BF
Call-ID: [email protected]
CSeq: 101 INVITE
Expires: 300
Min-SE: 1800
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Date: Mon, 09 May 2011 18:15:30 GMT
Supported: 100rel, timer, resource-priority, replaces, sdp-anat
Timestamp: 1304964930
User-Agent: Cisco-SIPGateway/IOS-12.x
Allow-Events: telephone-event
Content-Length: 0
Remote-Party-ID: <sip:[email protected]>;party=calling;screen=yes;privacy=off
Cisco-Guid: 681863951-2040467936-2449211428-335708344

20:15:31.344 [CM302001]: Authorization system can not identify source of: SipReq: INVITE [email protected]:5060 tid=FA898 cseq=INVITE [email protected]:5060 / 101 from(wire)
*****/snip*****

Any help would be appreciated...
Thanks,
Oliver
 
can you run the 3CX Firewall Checker

you can find this within the 3CX console under the settings menu

post the resaults here for us to check

you may find this URL useful http://www.3cx.com/blog/voip-howto/cisco-voip-configuration/
 
Hi,
the output from the firewall checker is at the end of this post.
Just as a reminder: I don't have a problem with the internet connection. This is working fine. But I do have a problem with our phone connection. And the Cisco router is not a firewall, but a PBX gateway.

Some more information, that might be helpful:
- both systems, 3cx and the router are in the same subnet (router: 192.168.60.1, 3cx 192.168.60.100)
- There's no firewall between the systems
- We use a dedicated public IP to allow the recommended ports to the 3cx and have already successfully enabled a bridge to a partner company, also running a 3cx. So the connection to the internet is working fine.

All the best,
Oliver

***** snip *****
3CX Firewall Checker, v1.0. Copyright (C) 3CX Ltd. All rights reserved.

<11:12:09>: Phase 1, checking servers connection, please wait...
<11:12:09>: Stun Checker service is reachable. Phase 1 check passed.
<11:12:09>: Phase 2a, Check Port Forwarding to UDP SIP port, please wait...
<11:12:16>: UDP SIP Port is set to 5060. Response received correctly with no translation. Phase 2a check passed.

<11:12:16>: Phase 2b. Check Port Forwarding to TCP SIP port, please wait...
<11:12:21>: TCP SIP Port is set to 5060. Response received correctly with no translation. Phase 2b check passed.

<11:12:21>: Phase 3. Check Port Forwarding to TCP Tunnel port, please wait...
<11:12:25>: TCP TUNNEL Port is set to 5090. Response received correctly with no translation. Phase 3 check passed.

<11:12:25>: Phase 4. Check Port Forwarding to RTP external port range, please wait...
<11:12:35>: UDP RTP Port 9000. Response received correctly with no translation. Phase 4-01 check passed.
<11:12:40>: UDP RTP Port 9001. Response received correctly with no translation. Phase 4-02 check passed.
<11:12:44>: UDP RTP Port 9002. Response received correctly with no translation. Phase 4-03 check passed.
<11:12:49>: UDP RTP Port 9003. Response received correctly with no translation. Phase 4-04 check passed.
<11:12:53>: UDP RTP Port 9004. Response received correctly with no translation. Phase 4-05 check passed.
<11:12:58>: UDP RTP Port 9005. Response received correctly with no translation. Phase 4-06 check passed.
<11:13:02>: UDP RTP Port 9006. Response received correctly with no translation. Phase 4-07 check passed.
<11:13:07>: UDP RTP Port 9007. Response received correctly with no translation. Phase 4-08 check passed.
<11:13:11>: UDP RTP Port 9008. Response received correctly with no translation. Phase 4-09 check passed.
<11:13:16>: UDP RTP Port 9009. Response received correctly with no translation. Phase 4-10 check passed.
<11:13:20>: UDP RTP Port 9010. Response received correctly with no translation. Phase 4-11 check passed.
<11:13:25>: UDP RTP Port 9011. Response received correctly with no translation. Phase 4-12 check passed.
<11:13:29>: UDP RTP Port 9012. Response received correctly with no translation. Phase 4-13 check passed.
<11:13:34>: UDP RTP Port 9013. Response received correctly with no translation. Phase 4-14 check passed.
<11:13:38>: UDP RTP Port 9014. Response received correctly with no translation. Phase 4-15 check passed.
<11:13:43>: UDP RTP Port 9015. Response received correctly with no translation. Phase 4-16 check passed.
<11:13:47>: UDP RTP Port 9016. Response received correctly with no translation. Phase 4-17 check passed.
<11:13:52>: UDP RTP Port 9017. Response received correctly with no translation. Phase 4-18 check passed.
<11:13:56>: UDP RTP Port 9018. Response received correctly with no translation. Phase 4-19 check passed.
<11:14:01>: UDP RTP Port 9019. Response received correctly with no translation. Phase 4-20 check passed.
<11:14:05>: UDP RTP Port 9020. Response received correctly with no translation. Phase 4-21 check passed.
<11:14:10>: UDP RTP Port 9021. Response received correctly with no translation. Phase 4-22 check passed.
<11:14:14>: UDP RTP Port 9022. Response received correctly with no translation. Phase 4-23 check passed.
<11:14:19>: UDP RTP Port 9023. Response received correctly with no translation. Phase 4-24 check passed.
<11:14:23>: UDP RTP Port 9024. Response received correctly with no translation. Phase 4-25 check passed.
<11:14:28>: UDP RTP Port 9025. Response received correctly with no translation. Phase 4-26 check passed.
<11:14:32>: UDP RTP Port 9026. Response received correctly with no translation. Phase 4-27 check passed.
<11:14:37>: UDP RTP Port 9027. Response received correctly with no translation. Phase 4-28 check passed.
<11:14:41>: UDP RTP Port 9028. Response received correctly with no translation. Phase 4-29 check passed.
<11:14:46>: UDP RTP Port 9029. Response received correctly with no translation. Phase 4-30 check passed.
<11:14:56>: UDP RTP Port 9030. Response received correctly with no translation. Phase 4-31 check passed.
<11:15:00>: UDP RTP Port 9031. Response received correctly with no translation. Phase 4-32 check passed.
<11:15:05>: UDP RTP Port 9032. Response received correctly with no translation. Phase 4-33 check passed.
<11:15:09>: UDP RTP Port 9033. Response received correctly with no translation. Phase 4-34 check passed.
<11:15:14>: UDP RTP Port 9034. Response received correctly with no translation. Phase 4-35 check passed.
<11:15:18>: UDP RTP Port 9035. Response received correctly with no translation. Phase 4-36 check passed.
<11:15:23>: UDP RTP Port 9036. Response received correctly with no translation. Phase 4-37 check passed.
<11:15:27>: UDP RTP Port 9037. Response received correctly with no translation. Phase 4-38 check passed.
<11:15:32>: UDP RTP Port 9038. Response received correctly with no translation. Phase 4-39 check passed.
<11:15:36>: UDP RTP Port 9039. Response received correctly with no translation. Phase 4-40 check passed.
<11:15:41>: UDP RTP Port 9040. Response received correctly with no translation. Phase 4-41 check passed.
<11:15:45>: UDP RTP Port 9041. Response received correctly with no translation. Phase 4-42 check passed.
<11:15:50>: UDP RTP Port 9042. Response received correctly with no translation. Phase 4-43 check passed.
<11:15:54>: UDP RTP Port 9043. Response received correctly with no translation. Phase 4-44 check passed.
<11:15:59>: UDP RTP Port 9044. Response received correctly with no translation. Phase 4-45 check passed.
<11:16:03>: UDP RTP Port 9045. Response received correctly with no translation. Phase 4-46 check passed.
<11:16:08>: UDP RTP Port 9046. Response received correctly with no translation. Phase 4-47 check passed.
<11:16:12>: UDP RTP Port 9047. Response received correctly with no translation. Phase 4-48 check passed.
<11:16:17>: UDP RTP Port 9048. Response received correctly with no translation. Phase 4-49 check passed.
<11:16:21>: UDP RTP Port 9049. Response received correctly with no translation. Phase 4-50 check passed.


Application exit code is 0
***** /snip *****
 
you may want to check your DID setup on the 3cx. when you built the sip trunk provider on the 3cx you had to use 1 number for the authenticaiton. did you test that number and does it work?
 
If you are able to get this to work I would be extremley interested in a copy/example of your configuration. I am needing to do the same thing with a T1 interface. I have tried this previously with asterisk and was unable to ever get a working configuration. I have seen one post in these forums about someone who got it to work but outbound DTMF would not pass. I have not seen that persons configuration though.
 
I found this post in another discussion, not sure if it might help.

Hi all,

can anyone provide a working example for a connection between a 3cx system and a Cisco 2811 (IOS 124.22T) router with PRI ?

My config example:

dial-peer voice 20000 voip
description xxxx
destination-pattern xxxx..
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.60.100
dtmf-relay rtp-nte
no vad

sip-ua
credentials username 20000 password xxxxxxx realm 3CXPhoneSystem
authentication username 20000 password xxxxxx retry invite 3
retry response 3
retry bye 3
retry cancel 3
timers expires 300000
registrar ipv4:192.168.60.100 expires 300
sip-server ipv4:192.168.60.100:5060

i have an outbound pots peer aswell

unfortunately, the router get´s blacklisted on the 3cx system...
 
I found this post back from 2007 in these forums....let me know if this helps at all:


I have a Cisco 2621XM router and have successfully configured it so that it acts as my VoIP gateway.

Hardware configuration is as follows:

NM-HD-2V with 1 2-port VIC2-2FXO card
IOS version: c2600-ipvoicek9-mz.124-9.T5.bin

Here's the necessary configuration to get things working on the Cisco router with 3CX PBX.

The code below tells the router what kind of VoIP service to use, which is set to sip

voice service voip
sip

Next, define the codecs you wish to you in order of preference.

voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8 bytes 40
codec preference 3 g723r63 bytes 96
codec preference 4 g726r16 bytes 80

Next configure your voice ports. This example is only for the first voice port. The last line is the most important as it tell the port what extension to dial on inbound call. The opx parameter tells the router that the extension is an off premise extension.

voice-port 1/0/0
no battery-reversal
timing hookflash-out 50
connection plar opx 999

Next program your dial-peers. Pick any arbitrary number for your dial-peers but they should make some sense to you. I've chosen 20000 for my voip dial-peer, which is used for inbound calls. If you have more than one voip dial-peer, set the preference order.

dial-peer voice 20000 voip
preference 1
destination-pattern 99.
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.253.5 --> address of 3CX server
dtmf-relay rtp-nte
no vad

Next program your POTS dial-peer.

dial-peer voice 10000 pots
preference 1 --> use if you have multiple POTS dial-peers
destination-pattern .T
port 1/0/0 --> matches your dial-peer with physcial port

Next program the SIP user agent parameters. The "authentication" parameter is used to authenticate the Cisco router against the gateway you programmed in the 3CX server.

sip-ua
authentication username 10000 password 091D1E594955
retry invite 3
retry response 3
retry bye 3
retry cancel 3
timers expires 300000
registrar ipv4:192.168.253.5 expires 300
sip-server ipv4:192.168.253.5:5060

The above should work for any Cisco router that supports VoIP.
 
I got some friends to send me some configs...keep in mind this is for a cisco call manager but it is still using this router as a SIP gateway so it should be very similar.


voice call send-alert
!
voice service voip
address-hiding
allow-connections sip to sip
redirect ip2ip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
sip
header-passing error-passthru
asserted-id pai
midcall-signaling passthru
privacy-policy passthru
g729 annexb-all
!
!
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
voice translation-rule 1
rule 1 /^91\(.*\)/ /\1/
rule 2 /^9\(.*\)/ /\1/

voice translation-profile DIGITSTRIP_9
translate called 1

dial-peer voice 100 voip
description Inbound SIP Dial-Peer for XXXXXXXXXX DIDs to Publisher from ATT
preference 2
destination-pattern ..........
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip profiles 1
session protocol sipv2
session target ipv4:10.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
!
dial-peer voice 101 voip
description Inbound SIP Dial-Peer for XXXXXXXXXX DIDs to Subscriber01 from A
preference 1
destination-pattern ..........
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip profiles 1
session protocol sipv2
session target ipv4:10.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
!
dial-peer voice 200 voip
description Outbound SIP Dial-Peer for National Dialing to ATT Primary
translation-profile outgoing DIGITSTRIP_9
preference 1
destination-pattern 9[2-9]..[2-9]......
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip privacy-policy passthru
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
incoming called-number .
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 201 voip
description Outbound SIP Dial-Peer for National Dialing to ATT Secondary
translation-profile outgoing DIGITSTRIP_9
preference 2
destination-pattern 9[2-9]..[2-9]......
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip privacy-policy passthru
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
incoming called-number .
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 202 voip
description Outbound SIP Dial-Peer for LongDistance Dialing to ATT Primary
translation-profile outgoing DIGITSTRIP_9
preference 1
destination-pattern 91[2-9]..[2-9]......
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip privacy-policy passthru
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 203 voip
description Outbound SIP Dial-Peer for LongDistance Dialing to ATT Secondary
translation-profile outgoing DIGITSTRIP_9
preference 2
destination-pattern 91[2-9]..[2-9]......
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip privacy-policy passthru
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 204 voip
description Outbound SIP Dial-Peer for InterNational Dialing to ATT Primary
translation-profile outgoing DIGITSTRIP_9
preference 1
destination-pattern 9011T
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 205 voip
description Outbound SIP Dial-Peer for InterNational Dialing to ATT Secondar
translation-profile outgoing DIGITSTRIP_9
preference 2
destination-pattern 9011T
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 206 voip
description Outbound SIP Dial-Peer for Emergency Dialing to ATT Primary
translation-profile outgoing DIGITSTRIP_9
preference 1
destination-pattern 911
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 207 voip
description Outbound SIP Dial-Peer for Emergency Dialing to ATT Secondary
translation-profile outgoing DIGITSTRIP_9
preference 2
destination-pattern 911
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 208 voip
description Outbound SIP Dial-Peer for Information Dialing to ATT Primary
translation-profile outgoing DIGITSTRIP_9
preference 1
destination-pattern 9411
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
dial-peer voice 209 voip
description Outbound SIP Dial-Peer for Emergency Information to ATT Secondar
translation-profile outgoing DIGITSTRIP_9
preference 2
destination-pattern 9411
rtp payload-type nse 99
rtp payload-type nte 100
voice-class codec 1
voice-class sip early-offer forced
voice-class sip profiles 1
session protocol sipv2
session target ipv4:12.x.x.x
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
!
!
sip-ua
no remote-party-id
retry invite 2
 
Any of you guys been able to setup a cisco router as a T1 gateway? Have a cisco voip supported router with both a chanelized and regular T1 hwic. noob with T1's in general. Thanks!
 
Status
Not open for further replies.
Get 3CX - Absolutely Free!

Link up your team and customers Phone System Live Chat Video Conferencing

Hosted or Self-managed. Up to 10 users free forever. No credit card. Try risk free.

3CX
A 3CX Account with that email already exists. You will be redirected to the Customer Portal to sign in or reset your password if you've forgotten it.