TryLearn More

Use SIP trunks, WebRTC & Apps

Slash your Phone Bill by 80%

Aatrox Communications

On this topic

Aatrox Communications

About Aatrox Communications

System Preparation

3CX Version

Provider Capabilities

Configuring the Trunk with 3CX

Adding the Trunk

Adding Additional DIDs

Creating Inbound Rules

Number Format

General

Outbound Caller ID

Outbound Rules

Additional Information

Caller ID on International Calls

About Aatrox Communications

Aatrox Communications is an Australian-based telecommunications provider which specialises in IP Telephony for small and large businesses. They offer a cost-effective and reliable unlimited or PAYG SIP Trunks, with local Australian support.

Reference website: Aatrox Communications

System Preparation

Before configuring the SIP trunk it is required to go through the following checklist and make changes where necessary:

Further setup information can be found in our Academy: 3CX Academy Basic Course

3CX Version

Some providers gained support and compatibility with 3CX on a specific product version. It is advisable to always run the latest version of 3CX to ensure ongoing compatibility.

Minimum 3CX Version: 3CX v15.5 SP2

Provider Capabilities

Below is a short overview of the provider's capabilities and services and whether they’re supported or not:

  • CLNS (Clip No Screening): No
  • Catch All Routing: Yes
  • Fax T.38 support: Yes
  • CLIR (Number Suppression):         Yes
  • DTMF via RFC 2833:        Yes
  • Codec Order: G711U, G711A, GSM-FR
  • NAT Support: Yes
  • SRTP - No

Configuring the Trunk with 3CX

The general instructions outlining how to add a new SIP Trunk to your 3CX installation can be found here.

Adding the Trunk

Go to “SIP Trunks” and select “Add SIP Trunk”

  • Select Country: AU
  • Select Provider in your Country: Aatrox Communications
  • Main trunk number: This will have been provided to you by Aatrox Communications. You must enter the number in the national number format (e.g. 0285203570)
  • Press OK

Under the “General” tab in the “Trunk Details” enter the registrar, and in the “Authentication” section your Authentication ID and Password (these will be supplied to you by Aatrox Communications).

Once you have filled in these fields as given to you by Aatrox Communications, scroll to the top of the page and press OK. At this point if you refresh the page you should see your Aatrox Communications Trunk appear as Registered.

Adding Additional DIDs

To associate all other DIDs/Numbers you have in your  Aatrox Communications account with 3CX, go to the Management Console → SIP Trunks, double-click on your  Aatrox Communications Trunk and go to the “DIDs” tab.

Here you should already see 1 entry; that is the Main Trunk number you have set. Add all other DIDs/Numbers you have to the list in a national number format (e.g. 0285203570) and press OK.

Creating Inbound Rules

Now that you have associated all your DIDs/Numbers with your SIP Trunk in 3CX, you can create Inbound Rules to set where calls will be routed when those numbers are called. Instructions on how to create Inbound Rules can be found here.

Number Format

General

When configuring Aatrox Communications SIP Trunks in 3CX, all numbers should be entered in a national number format (e.g. 0285203570), otherwise call routing will fail.

Outbound Caller ID

Aatrox Communications Trunks does not support Clip No Screening which means you can only present numbers as Outbound Caller ID that are assigned to your trunk. These numbers must be presented in a national format (e.g. 0285203570).

Outbound Rules

When configuring your Outbound Rules make sure that all numbers are dialed either in the National (e.g. 0285203570) or  International (e.g. 001161285203570) format. More information about how to create Outbound Rules and how they work can be found here.

Additional Information

Caller ID on International Calls

Upon testing it was observed that international incoming calls were presented as Anonymous and not with a caller ID.

Free for up to 1 year! Select preferred deployment:

On-Premise

for Linux on a $200 appliance or as a VM

Get the ISO

On-Premise

for Windows as a VM

Download the setup file

On the cloud

In your Google, Amazon, Azure account

Take the PBX Express