Search results

  1. Grandstream HandyTone HT503 FXO Gateway

    Re: "Unsupported IP Phone" HandyTone HT503 FXO Gateway lneblett, when you say "Do the peer SIP trunk method only" can you kindly explain the steps if possible? Here is how the HT is connected: There is a line port which is the FXO port, this goes directly to the wall phone socket. Then from...

  2. Grandstream HandyTone HT503 FXO Gateway

    Re: "Unsupported IP Phone" HandyTone HT503 FXO Gateway Also, the unconditional forwarding of a call to VOIP extension seems to have a lot of interference noise and volume seems extremely low. Any ideas how I can improve this?

  3. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I think I know why it's not working, I think the Patton device i've got doesnt actually have FXO ports, I think the 4 ports are FXS. I checked it against a document on the patton website and it says 4 FXS ports. It's the SN4114/JS/EUI model. Does that mean the device is useless for what I want...

  4. Grandstream HandyTone HT503 FXO Gateway

    Re: "Unsupported IP Phone" HandyTone HT503 FXO Gateway lneblett, under the basic settings I have set the unconditional call forward to voip set to an extension. Under FXO settings I specified a extension and password that I created. So now when I receive a call it comes through but the caller...

  5. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    Thanks for your reply. It's not blacklisted. However, I have made a slight breakthrough. I tried to set ports as 1 and channels as 1 but this time I was getting a 404 Not Found/INVITE error in the activity log and i wasnt getting busy tone. So decided to set it to 4 ports and 4 channels and...

  6. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I followed the following guide 100% http://www.3cx.com/voip-gateways/patton ... de-sn4112/ Did every step of it and it all matches up with these steps. But still no success. Only difference is in step 2 where I changed ports from the example 2 to 4 as my device has 4 ports. And in step 4 where...

  7. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    IP address does match, it was auto generated config file through the wizard. The only place I can edit the IP address of the gateway is in the section PSTN gateways. Not in the ports/trunks section.

  8. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I think that failed Auth is when I deleted the PSTN Gateway to try and add it again and it was failing. The Patton Gateway IP is 172.16.0.3 I clicked on ports/trunks and the 90001 virtual extension is registered but when i click on it to edit it there isnt any trunk settings to set to "send"...

  9. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    Yes extension to extension calls all work fine.

  10. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    Here is the Event Log just has a repeat of the following two lines everytime I attempt to make a call: Call or Registration to 0800XXXXXX@(Ln.90001@Patton) has failed. [ V4 172.16.0.3:5060 UDP target domain=unspecified mFlowKey=944 ] replied: 600 Busy Everywhere; from IP:172.16.0.3:5060 Device...

  11. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    leejor, thanks. I've tuned the outbound rules and still no luck. I keep getting busy tone and looking at the activity log it gives me error: 600 Busy Everywhere for that event. I have my telephone line plugged into port 0 on the SN4114. Even when following online guides, the online guides seem...

  12. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I checked the Port/Trunks section in 3CX and the Patton gateway shows up a registered(idle) But when I make a call using the outbound route i just keep getting a line busy tone. There are 4 ports on the patton, do I nee to specify which port I am using?

  13. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I put 4 ports but used only one channel and at the end the 3cx did show me the virtual extension number, auth_id and password. I didnt check to see if it was registered, which section do I go to?

  14. Configuring Patton SmartNode SN4114 VoIP Media Gateway

    I bought a Patton SmartNode SN4114 VoIP media gateway with 4 FXS and FXO Ports. I want to use it to receive and make calls on my Analog PSTN line. I followed the 3CX guide and tried the following but none seem to work. First method I tried is as follows: * Went to Add Gateway and gave it a...

  15. Grandstream HandyTone HT503 FXO Gateway

    I am new here and trying out 3CX for the first time, coming from using asterisk for many years. I have a Grandstream HandyTone HT503 FXO Gateway which I had working on my Asterisk system by creating a dedicated extension for it and then creating a SIP trunk to use the HT503 for inbound and...
View older results
3CX Logo Footer Copyright © Sitemap Privacy
Top Bottom