Search results

  1. Cisco SPA525G2 phones and network reliablity

    Spoke too soon, one extension is now not responding to a new call. Both 3cx and the web interface shows it registered.

  2. Cisco SPA525G2 phones and network reliablity

    Possibly Resolved: Cisco SPA525G2 phones and network reliabl Possibly resolved. I disabled Supports Re-Invite and Supports Replaces header on one extension and rebooted both phones. My hold test has run for 25 minutes on the phone I changed. The hold test failed after 18 seconds on the...

  3. Cisco SPA525G2 phones and network reliablity

    This is an odd test but the other thing I notice is if I call the cisco phones from another phone. Answer with speaker and then from the calling phone I put the call on hold. The music plays on the cisco and about every 10 seconds I hear a beep. After about 30 seconds the phone goes into hell...

  4. Cisco SPA525G2 phones and network reliablity

    I ordered in 2 2.5a Cisco power supplies for these phones and they still have the same odd behaviors with one exception. Historically, when the phone would go exhibit the behavior where you would get one ring and then about 2 min later a missed call notification would appear, you would have to...

  5. Cisco SPA525G2 phones and network reliablity

    And looking at the fine print on the back of the Cisco phone it says 5v 2000ma

  6. Cisco SPA525G2 phones and network reliablity

    Just a random thought, what are the power requirements of these phones and how are you powering them? I don't have POE in my test area and was using power supplies from our grandstream phones. 5vdc 1200ma

  7. Cisco SPA525G2 phones and network reliablity

    Interesting changing the duplex rate did not seem to make a difference. After sitting a while, both phones experienced the condition I described with the phone not responding to 3cx. It is pingable but does not respond to a call and any inbound calls go to voicemail. 3CX shows it registered...

  8. Cisco SPA525G2 phones and network reliablity

    Just a quick question, I see the speed and duplex settings in the static ip section of the configuration. Confirming that I'm in the right spot and that the phone will respect the settings even if it is configured as dhcp? Thanks

  9. Cisco SPA525G2 phones and network reliablity

    Thanks for the replies, for some reason I did not get the board notifications. Will test with the speed and duplex settings and post back. These are in a very simple environment, no managed switches.

  10. Cisco SPA525G2 phones and network reliablity

    To preface the issue, we have polycom, yealink and grandstream phones in the office. None of which have the following issue. I have 2 SGA525G2's that I'm testing. Started out with 1 ran into the following issues and had the vendor send me a second one. Both behave the same. But I don't think...

  11. 3CX SIP Proxy Manager (Feature Request)

    Sorry to post here but the feature request forum is locked. The SIP Proxy Manager requires and IP address for the Remote Server. It would be useful if a hostname could be defined here. Example, our office has a dual wan router and we have DNS failover configured where we host our DNS...

  12. Polycom provisioning, adding options to template

    Hello, I have edited the default template and created my own specifically for the IP550. I have confirmed that my phone is calling the new template and not the original default polycom template. In my new template I have added/modified the following: in the <reg I have added...

  13. Polycom - Multiple Incoming Calls Per Phone

    Did you check the box in the extension setup to allow multiple calls?

  14. Testing Cisco SP501G LOW Priority

    Factory reset done, same issue with status light blinking on reboot but the blf's and reboot from 3cx work. Going to stick with and recommend the Polycom's for the site I'm quoting. The blinking status light on reboot is going to drive people nuts. It clears when you check voicemail but most...

  15. Testing Cisco SP501G LOW Priority

    I'll give it a shot, it was new in box but who knows...

  16. Testing Cisco SP501G LOW Priority

    I got my hands on an SPA501G and update it to firmware 7.4.6 as per the doc and configure it to auto provision. Once registered, I noticed the following odd behavior. The extension always shows as calling on other users 3cx assistant. Rebooting the phone from the phone tab in the admin...
View older results
3CX Logo Footer Copyright © Sitemap Privacy
Top Bottom