3CX Generating a bad Patton SN4112 Configuration file

[bdgarcia]

Hi

I have generated a configuration file for a PATTON SN4112 FXO gateway. I cannot get the auto upload to work, but I have been able to manually upload via the Web Console. After it reloads I get these errors:



Waiting for Ethernet link (PHY:0) .... done
Waiting for BOOTP information ................Can't get BOOTP info, using default IP address
Ethernet eth0: MAC address 00:a0:ba:10:62:7b
IP: 172.16.40.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Version v2_0_1 - Built 08:49:35, Oct 13 2017

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
SN4112/JO/EUI (MPC870 @ 65.536000 MHz)

RAM : 0x00000000 - 0x02000000, 0x00025678 - 0x01ffd000 available
FLASH: 0x60000000 - 0x60800000, 128 blocks of 0x00010000 bytes each.

Press ^C to abort boot script, press enter to start immediately
Executing boot script in 1 seconds
RedBoot> fis load
Loaded 2802108 bytes from 0x60040008 to 0x01800100 (entry 0x01800100)
RedBoot> go

Starting 'Firmware R6.9 2017-03-13' at 0x01800100 via 0x01800100

System type is SN4112/JO/EUI, 0004-0004
Serial No. 00A0BA10627B

Proceed with standard boot.

Checking PLDs...
Planar board : checking - please wait (this may take some seconds)
PLD OK, Version = 0x00040103

Installing Drivers...
Ethernet 0/0, MAC Addr 00:A0:BA:10:62:7B, RxQ 32, TxQ 64

Starting Modules...
2020-07-11T06:02:15 : Target Shell
All modules successfully started
Config startup-config READ [ OK ]
Config startup-config EXECUTE 2020-07-11T06:02:44 : LOGWARNING : Errors in configuration of router 'switch' ('show call-router switch reload' for details)
2020-07-11T06:03:06 : LOGINFO : Link up on interface ethernet 0 0 0
2020-07-11T06:03:07 : LOGINFO : Link up on interface IF_IP_LAN
[FAILED]
2020-07-11T06:03:14 : LOGWARNING : Config: Line 19: SN4112/JO/EUI(ic-voice)[0]#sntp-client
2020-07-11T06:03:14 : LOGWARNING : Config: % ^ Keyword mismatch
2020-07-11T06:03:14 : LOGWARNING : Config: Line 21: SN4112/JO/EUI(ic-voice)[0]#sntp-client server primary pool.ntp.org
2020-07-11T06:03:14 : LOGWARNING : Config: % ^ Keyword mismatch
2020-07-11T06:03:14 : LOGWARNING : Config: Line 220: SN4112/JO/EUI(prt-eth)[0/0]#port ethernet 0 1
2020-07-11T06:03:14 : LOGWARNING : Config: % Ethernet port does not exist
2020-07-11T06:03:14 : LOGWARNING : Config: Line 238: 192.168.57.13(prt-fxo)[0/1]#port fxo 0 2
2020-07-11T06:03:14 : LOGWARNING : Config: % Port 2 on slot 0 does not exist.
2020-07-11T06:03:14 : LOGWARNING : Config: Line 244: 192.168.57.13(cfg)#port fxo 0 3
2020-07-11T06:03:14 : LOGWARNING : Config: % Port 3 on slot 0 does not exist.
2020-07-11T06:03:14 : LOGWARNING : Config: Line 253: 192.168.57.13(ctx-cs)[switch]#no IF_FXO_2
2020-07-11T06:03:14 : LOGWARNING : Config: % ^ Keyword mismatch
2020-07-11T06:03:14 : LOGWARNING : Config: Line 254: 192.168.57.13(ctx-cs)[switch]#no IF_FXO_3
2020-07-11T06:03:14 : LOGWARNING : Config: % ^ Keyword mismatch
2020-07-11T06:03:14 : LOGWARNING : Config: Line 259: 192.168.57.13(ctx-cs)[switch]#port fxo 0 2
2020-07-11T06:03:14 : LOGWARNING : Config: % Port 2 on slot 0 does not exist.
2020-07-11T06:03:14 : LOGWARNING : Config: Line 261: 192.168.57.13(cfg)#port fxo 0 3
2020-07-11T06:03:14 : LOGWARNING : Config: % Port 3 on slot 0 does not exist.

Opening Modules...
All modules successfully opened
System is up.

2020-07-11T06:03:16 : LOGINFO : Warm start.

I have it getting it IP configuration using a static DHCP reservation. The unit seems to work fine until I upload the config. Once I upload the config, the IP configuration appears to be lost, and I have to factory reset. Once I factory reset all is fine until I upload the configuration the unit is hosed again.

I have attached the configuration file in case that gives any clues.

I am using the 6.9 firmware for the Patton.

I remember when I setup my 1st 4112 it is was a NIGHTMARE, and it seems 9 years later nothing has changed.

Any help is greatly appreciated.

I am also running the late version 16 3CX software for Windows.

 

[AWS2P]

Perhaps help from a Patton expert as @eddv123 may help you to fix

 

[eddv123]

The IP configuration side of things can be confusing at times however your file clearly states that your WAN interface is on DHCP and LAN 192.168.57.13 with a class C subnet.

If you use Advanced IP scanner on your local network does it pick up the Patton ? what if you swap ethernet cables into the other physical ethernet port (I am assuming your model has a second port).
https://www.advanced-ip-scanner.com/

Also regarding the configuration upload (as per the below) this requires manual upload to the Patton's interface and cannot be done in an auto-configuration fashion like the phones: https://www.3cx.com/voip-gateways/patton-smartnode-sn4112/

I am not sure why you are seeing those error lines however your configuration and firmware match what they should be to work.