Hello!
Great job you have done! I encounter some problems though.....
I have a swedish SIP company (cellip)
I have installed the PBX, latest version (beta 2)
I have softphones at another machines, that can do internal calls.
I have set up an VOIP Provider (cellip.com) and a line to it (gives status green/ok)
I have set the Basic Rule to that provider (just changed to the one mentioned)
The PBX registers at cellip. I have a webpage at the VOIP-provider to see that (below is the main response):
Logon has been done from IP-adress:
3CXPhoneSystem;rinstance=413ef513440b4205
...but I can not phone out or in.
usually it is a IP when I use a direct softphone. Can I get the PBX to register a IP instead of 3CXPhoneSystem;rinstance=413ef513440b4205 ?
I have a simple firewall (Barricade 7004br) with no specific restrictions.
I have tried to do prot forward at ports: 5060-5061,16384-16482,9000-9003
It is possible to use a softphone directly to cellip. Then I also fill in
Firewall traversal : IP-adress: =Use local adress
'Enable ICE',
and
Domain proxy : sip.mysecretary.net
I cant see if/how I can do that in PBX.
I try to dial out , and starting with an extra 0
the log says, it doesnt try to call out ? (err 403):
22:23:42.829 CallConf::saveCallEvent Incoming c18 "101"<sip:[email protected]> <sip:[email protected]> Incoming call (before routing)
22:23:42.839 CallConf::saveCallEvent Rejected c18 "101"<sip:[email protected]> <sip:[email protected]> Caller is not resolved or forbidden, sent 403 response
22:23:42.849 CallConf::saveCallEvent Terminated c18 "101"<sip:[email protected]> <sip:[email protected]> Call ended
The register of the PBX to VOIP-provider looks fine (?)
21:59:16.080 LineImpl::registered Line [#46855110848 @cellip] has been registered at provider
All lines (one external and two internal) is on hook.
I have sent this as a supportmail aswell with the debugfile.
Great job you have done! I encounter some problems though.....
I have a swedish SIP company (cellip)
I have installed the PBX, latest version (beta 2)
I have softphones at another machines, that can do internal calls.
I have set up an VOIP Provider (cellip.com) and a line to it (gives status green/ok)
I have set the Basic Rule to that provider (just changed to the one mentioned)
The PBX registers at cellip. I have a webpage at the VOIP-provider to see that (below is the main response):
Logon has been done from IP-adress:
3CXPhoneSystem;rinstance=413ef513440b4205
...but I can not phone out or in.
usually it is a IP when I use a direct softphone. Can I get the PBX to register a IP instead of 3CXPhoneSystem;rinstance=413ef513440b4205 ?
I have a simple firewall (Barricade 7004br) with no specific restrictions.
I have tried to do prot forward at ports: 5060-5061,16384-16482,9000-9003
It is possible to use a softphone directly to cellip. Then I also fill in
Firewall traversal : IP-adress: =Use local adress
'Enable ICE',
and
Domain proxy : sip.mysecretary.net
I cant see if/how I can do that in PBX.
I try to dial out , and starting with an extra 0
the log says, it doesnt try to call out ? (err 403):
22:23:42.829 CallConf::saveCallEvent Incoming c18 "101"<sip:[email protected]> <sip:[email protected]> Incoming call (before routing)
22:23:42.839 CallConf::saveCallEvent Rejected c18 "101"<sip:[email protected]> <sip:[email protected]> Caller is not resolved or forbidden, sent 403 response
22:23:42.849 CallConf::saveCallEvent Terminated c18 "101"<sip:[email protected]> <sip:[email protected]> Call ended
The register of the PBX to VOIP-provider looks fine (?)
21:59:16.080 LineImpl::registered Line [#46855110848 @cellip] has been registered at provider
All lines (one external and two internal) is on hook.
I have sent this as a supportmail aswell with the debugfile.
