I went about setting up a tunnel for my hardphones using the instructions found here:
https://www.3cx.com/docs/3cx-tunnel-session-border-controller/ - new link
My system is set up thusly:
Local IP 3cx: 192.168.0.12
Public IP 3cx: 64.50.120.x
Local IP Hardphone: 192.168.1.104
Local IP Proxy Computer: 192.168.1.102
Port 5090/TCP forwarded from 64.50.120.x to 192.168.0.12
First went about setting up the proxy. To that end, I put the following numbers in the following places:
IP or FQDN: 192.168.0.12
Authentication: 3cx Phone System, 407/407
On Tunnel:
Check box "Use Tunnel to Connect."
Use tunnel of host: 192.168.1.102
Remote End of Tunnel: 64.50.120.x
Tunnel password: xxx
Click close, then login to new profile.
I get a display (I'm using desktop mode) of current line status of everybody (like the old Call Assistant used to do). So far, so good, I think. Extension 407 shows up as unregistered, however. I think that perhaps that's the hardphone's trouble, not mine. So I go about setting up my hardphone. I'm using a Linksys SPA-922. My other deployed phone is GS Budgetone 200, but I like the SPA phones better. Here's the settings for that:
Proxy: 192.168.0.12
Outbound Proxy: 192.168.1.102:5080 (also tried it with no port number)
Use Outbound Proxy: Yes
Use Outbound Proxy in Dialog: Yes
Display name 407
User ID, Password, and Auth ID are all set to 407.
Use Auth ID is set to yes.
Phone still doesn't show as registered after a reboot however. I can view status with the 3cx VOIP Client, and it shows the tunnel as being connected. But no registration, and nothing shows up in the logs.
Running a netstat at the command line shows my tunnel connection to my PBX, but just listening on port 5080 for a phone to register, which it never does.
Any thoughts?
https://www.3cx.com/docs/3cx-tunnel-session-border-controller/ - new link
My system is set up thusly:
Local IP 3cx: 192.168.0.12
Public IP 3cx: 64.50.120.x
Local IP Hardphone: 192.168.1.104
Local IP Proxy Computer: 192.168.1.102
Port 5090/TCP forwarded from 64.50.120.x to 192.168.0.12
First went about setting up the proxy. To that end, I put the following numbers in the following places:
IP or FQDN: 192.168.0.12
Authentication: 3cx Phone System, 407/407
On Tunnel:
Check box "Use Tunnel to Connect."
Use tunnel of host: 192.168.1.102
Remote End of Tunnel: 64.50.120.x
Tunnel password: xxx
Click close, then login to new profile.
I get a display (I'm using desktop mode) of current line status of everybody (like the old Call Assistant used to do). So far, so good, I think. Extension 407 shows up as unregistered, however. I think that perhaps that's the hardphone's trouble, not mine. So I go about setting up my hardphone. I'm using a Linksys SPA-922. My other deployed phone is GS Budgetone 200, but I like the SPA phones better. Here's the settings for that:
Proxy: 192.168.0.12
Outbound Proxy: 192.168.1.102:5080 (also tried it with no port number)
Use Outbound Proxy: Yes
Use Outbound Proxy in Dialog: Yes
Display name 407
User ID, Password, and Auth ID are all set to 407.
Use Auth ID is set to yes.
Phone still doesn't show as registered after a reboot however. I can view status with the 3cx VOIP Client, and it shows the tunnel as being connected. But no registration, and nothing shows up in the logs.
Running a netstat at the command line shows my tunnel connection to my PBX, but just listening on port 5080 for a phone to register, which it never does.
Any thoughts?
Last edited by a moderator:
