Unidata WPU-7800 cannot make calls but CAN receive them

[--mark--]

Before I start, thank you in advance for any insight to nudge me in the right direction for fixing this, I'm sure I'm not far off :roll:

We have a requirement for a WiFi handset, this Unidata WPU-7800 seems to be a good choice, reasonably quality and price. There is mention of this phone on the forum boards of people successfully using them. Because it can't be autoprovisioned by 3CX I'm having to try to configure it manually. I have configured it with it's built-in web interface as well as on 3CX. The phone will receive calls fine from other internal extensions but trying to make calls fails both internally and externally. I notice in the logs (please see below) that the call is rejected "caller is unknown" but I can't quite figure out the bit I'm not getting! Any info greatly appreciated.

When dialling from the Unidata, I try 40 and SEND key and get a message "Unassigned address" on the handset, this doesn't appear to try to make a call.

When I try 40# and SEND key the handset reports "Connection failed" and the server log fills up with the information below. The deskphone is extension 40, the WiFi handset is 54. I've replaced our domain name with "companyname" to save me blushes

The SIP settings of the phone are configured as follows:

Local Port (5000~40000) > 5060
T1 (0isable, 100~65535) > 500
T2 (0isable, 100~65535) > 4000
T4 (0isable, 100~65535) > 5000
Timer B (0isable, 500~65535) > 0
Timer F (0isable, 500~65535) > 0
Use User Agent > on
User Agent Name > 54
Use Version On User Agent > off
Use Vendor ID On User Agent > off
Use MAC On User Agent > off
Max Forwards (0~999) > 70
Retry Hold On 491 > on
Caller ID Mode > default
ICT Transaction Max Count (0~100) > 20
Use rport > off
Enable STUN OPTIONS > on
Options Expire (0~86400) > 20
Request REFER Timeout (0isable, 200~32000) > 200
Wait REFER Response Timeout (0isable, 500~32000) > 8000
180 Retransmission Interval (0isable, 1~3600) > 60
Invite Expire (0isable, 10~86400) > 180
Reuse Auth Header Within Dialog > off
Register Contact Change > on
Use Remove All Contact > off
Use Random Contact > off
Retry To Redirect Contact > on
Auth Retry Count (1~10) > 1
Retry Register After Auth Fail > on
Ignore 183 Without SDP > off
Illegal UserName Check At Request URI > off
Remove Register On Start > off
Check Escape Of Call Number > off
Transaction Delete Before L3HANDOVER > on

and a representative logfile of what I'm seeing when trying to make a call:

09:29:56.912  [CM502001]: Source info: From: "STORES"<sip:[email protected]>;tag=2089018456<sip:40%[email protected]>
09:29:56.912  [CM503013]: Call(1177): Incoming call rejected, caller is unknown; msg=SipReq:  INVITE 40#@companyname.local tid=1131176229 cseq=INVITE [email protected] / 21 from(wire)
09:29:56.800  [CM500002]: Unidentified incoming call. Review INVITE and adjust source identification:
  INVITE sip:40%[email protected] SIP/2.0
  Via: SIP/2.0/UDP 192.168.192.156:5060;branch=z9hG4bK1656478042
  Max-Forwards: 70
  Contact: <sip:[email protected]>
  To: <sip:40%[email protected]>
  From: "STORES"<sip:[email protected]>;tag=2089018456
  Call-ID: [email protected]
  CSeq: 20 INVITE
  Expires: 180
  Session-Expires: 600;refresher=uac
  Supported: replaces, 100rel, timer
  User-Agent: 54-v2.1.12/00:03:2a:24:f9:52
  Content-Length: 0
  
09:29:56.800  [CM302001]: Authorization system can not identify source of: SipReq:  INVITE 40#@companyname.local tid=1656478042 cseq=INVITE [email protected] / 20 from(wire)
09:29:51.457  Currently active calls - 1: [1169]
09:29:46.038  [CM503008]: Call(1176): Call is terminated
09:29:43.365  [CM503007]: Call(1176): Device joined: sip:[email protected]:5060
09:29:43.363  [CM503007]: Call(1176): Device joined: sip:[email protected]:5060
09:29:41.834  [CM505001]: Ext.54: Device info: Device Not Identified: User Agent not matched; Capabilities:[reinvite, replaces, able-no-sdp, recvonly] UserAgent: [54-v2.1.12/00:03:2a:24:f9:52] PBX contact: [sip:[email protected]:5060]
09:29:41.834  [CM503002]: Call(1176): Alerting sip:[email protected]:5060
09:29:41.544  [CM503025]: Call(1176): Calling Ext:Ext.54@[Dev:sip:[email protected]:5060]
09:29:41.514  [CM503004]: Call(1176): Route 1: Ext:Ext.54@[Dev:sip:[email protected]:5060]
09:29:41.500  [CM503010]: Making route(s) to <sip:[email protected]>
09:29:41.496  [CM505001]: Ext.40: Device info: Device Identified: [Man: Cisco;Mod: SPA Series;Rev: General] Capabilities:[reinvite, replaces, unable-no-sdp, no-recvonly] UserAgent: [Cisco/SPA504G-7.4.8a] PBX contact: [sip:[email protected]:5060]
09:29:41.494  [CM503001]: Call(1176): Incoming call from Ext.40 to <sip:[email protected]>

 

[--mark--]

I seem to have made some progress. The phone can now make outgoing calls, but only to numbers that are 3 digits or longer, which essentially means external calls only.

Our 3CX setup is using 2 digit extension numbers, the phone reports "Unassigned Address" when I try these.

If I call 40# I get "Connection Failed"

If I call *777 (echo test) this works fine.

I know someone out there knows the answer!

 

[efounco]

This sounds like a dialing rule issue.

Access the phone's built in WEB interface. Make sure the dial rule is set to accept * (everything). By default, some phones are set to accept only 3 or more numbers.

 

[enterprise4]

Please be so kind as to sned me the provisoning template you used for the Unidata WPU-7800.

Thanks in advance,
Rich
[email protected]

 

[leejor]

09:29:56.912 [CM503013]: Call(1177): Incoming call rejected, caller is unknown; msg=SipReq: INVITE 40#@companyname.local tid=1131176229 cseq=INVITE [email protected] / 21 from(wire)
09:29:56.800 [CM500002]: Unidentified incoming call. Review INVITE and adjust source identification:
INVITE sip:40%[email protected] SIP/2.0

I'm not certain if you are still getting the log (above), that you posted earlier. When using an internal extension, you should be using the IP of the server, not a name. When dealing with an external extension, you can use a URL, but, must put that in the Domain Name setting in the PBX. This is quite common when your pubic IP is dynamic, and you use a service such as DynDNS.