Configuring Patton SN-4634 VoIP gateway

[Zeljko]

Is there anybody that know how to configure Patton SN-4634 ISDN BRI gateway with 3CX?
I was find on VoIP Gateway config. guides http://www.3cx.com/voip-gateways/smartnode-isdn.html that there is in Gateway Created section some button "Generate config file" but I can't find it.

Please help!

 

[5qg4]

Please try to modify the IP address, virtual extension and password of virtual extension this sample cfg file then import to your device. Please backup your existing cfg first. Hope this can help.

WAN IP: 10.39.100.251
Default gateway: 10.39.100.254
PBX IP: 10.39.100.252
virtual extension: 1001
virtual extension PWD: 1001

sample cfg for SN-4634
-------------------------------
cli version 3.20
webserver port 80 language en
sntp-client
sntp-client server primary 10.39.100.252 port 123 version 4
system hostname SN4634

system

ic voice 0

system
clock-source internal

profile ppp default

profile tone-set default

profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
codec 2 g711ulaw64k rx-length 20 tx-length 20

profile pstn default

profile sip default

profile aaa default
method 1 local
method 2 none

context ip router

interface ETH0_0
ipaddress 10.39.100.251 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu

interface ETH0_1
ipaddress 192.168.1.1 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu

context ip router
route 0.0.0.0 0.0.0.0 10.39.100.254 0

context cs switch
digit-collection timeout 4
no digit-collection terminating-char
address-completion timeout 20
national-prefix 0
international-prefix 00

routing-table called-e164 TAB-OUT
route .%T dest-service BRIHUNT MT_ITC

mapping-table itc to itc MT_ITC
map default to speech

interface isdn BRI0_0
route call dest-interface SIP_1
address-complete-indication emit set

interface isdn BRI0_1
route call dest-interface SIP_1
address-complete-indication emit set

interface isdn BRI0_2
route call dest-interface SIP_1
address-complete-indication emit set

interface isdn BRI0_3
route call dest-interface SIP_1
address-complete-indication emit set

interface sip SIP_1
bind gateway AST_1
service default
route call dest-table TAB-OUT
remote-party-id called-party
remote-party-id calling-party

service hunt-group BRIHUNT
drop-cause normal-unspecified
drop-cause no-circuit-channel-available
drop-cause network-out-of-order
drop-cause temporary-failure
drop-cause switching-equipment-congestion
drop-cause access-info-discarded
drop-cause circuit-channel-not-available
drop-cause resources-unavailable
drop-cause user-busy
drop-cause destination-out-of-order
route call 1 dest-interface BRI0_0
route call 2 dest-interface BRI0_1
route call 3 dest-interface BRI0_2
route call 4 dest-interface BRI0_3
route call 5 dest-interface BRI0_0
route call 6 dest-interface BRI0_1
route call 7 dest-interface BRI0_2
route call 8 dest-interface BRI0_3

context cs switch
no shutdown

gateway sip AST_1
bind interface ETH0_0 router

service default
default-server 10.39.100.252 loose-router
registration-lifetime 1000
registrar 10.39.100.252
user 1001 display-name 1001 password 1001

gateway sip AST_1
no shutdown

port ethernet 0 0
medium auto
encapsulation ip
bind interface ETH0_0 router
no shutdown

port ethernet 0 1
medium auto
encapsulation ip
bind interface ETH0_1 router
no shutdown

port bri 0 0
clock auto
encapsulation q921

q921
protocol pp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface BRI0_0 switch

port bri 0 0
no shutdown

port bri 0 1
clock auto
encapsulation q921

q921
protocol pp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface BRI0_1 switch

port bri 0 1
no shutdown

port bri 0 2
clock auto
encapsulation q921

q921
protocol pp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface BRI0_2 switch

port bri 0 2
no shutdown

port bri 0 3
clock auto
encapsulation q921

q921
protocol pp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface BRI0_3 switch

port bri 0 3
no shutdown

port bri 0 4
clock auto
encapsulation q921

q921
protocol pmp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side net

port bri 0 4
shutdown

 

[Zeljko]

Patton SN4634 config problems

Hi Ricky,

Thank you very much for config file for Patton 4634, now is gateway registered but we still have a problems when we try to call ISDN numbers from outside.
So we cannot get incoming calls via Patton gateway.

This is server log for this problem:

[CM010001] Line configuration does not allow identification of the source of this call. Check Advanced Options for Gateways and Providers and match a field to a correct value from the following: Contact IP: '192.168.178.70'; From: '6195094'; To: '013751277'; Rline: '013751277'; Contact: '6195094'

Maybe we need to put MSN numbers somewhere in patton?
If you know where is the problem please let me know.

Thanks a lot!

zeljko

 

[miraportuga]

Go to the patton gateway configuration under 3cx Web admin page, "Other Options", select "Use ip in contacts" and below put 192.168.178.70

you should have no problem after that

Cheers

 

[Zeljko]

Patton SN4634 config problems

Hi,

we are change this option on 3CX but still don't work.

this is new server log:
[CM210001] Ambiguous configuration.3 source lines correspond to incoming call.INVITE Parameters: Contact IP: '192.168.178.70'; From: '6195094'; To: '013751277'; Rline: '013751277'; Contact: '6195094'. Line:CfgExtLine:1001 used as fallback!

any other idea?

zeljko

 

[miraportuga]

Tell me something, thats a 4 port gateway or something? (im not familiar with parrong devices)
If so, on 3CX Web admin page you have 1 line? or 4 lines? for all 4 ports of the gateway ? If im not wrong you will have to do the same thing on each line you have set up there coming from patton....
If that doesnt help then... i dont know :|

Cheers

 

[Zeljko]

Yes, this is ISDN 3BRI gateway (3 BRI digital lines) but each line have a 2 channels.
So, we have 3 registered PSTN lines on 3CX and all are green.
but cannot receive call throuth this gateway.

 

[5qg4]

Hi Zeljko,

All works except inbound calls? Or just can register 3CX box?

 

[N_G]

Did you use the generated config file?

Also check that your ISDN lines are point to point or point to multi point.

Then check that the gateway is set to same, ie that it expects same type of lines. You have to issue a command to do this (dont have it handy but should be in config file or patton manual)

Once thats checked, make inbound call check server status log and post here....

 

[Zeljko]

Hi Ricky,

Yes, outbound calls via this Patton IAD works fine, we only cannot get inbound calls. And all 3 BRI lines are registered.

Zeljko

 

[5qg4]

Hi Zeljko,

Can you post the debug trace of SmartNode when use command below.
#debug ccisdn error
#debug ccisdn signaling
#debug isdn error

Then place one call to your SN. I just make sure that any DID into your SN.

 

[Zeljko]

Hi Nick,

The config file generated via 3CX definitelly don't work bcz. my Patton hang-on after we import this config file.
On the other side the config file which I get from Ricky works but have problems with inbound calls only.

Please check what is wrong with config script in 3CX vizard.
Tray to make config from your side for Patton 4634.

Zeljko

 

[deangelisg]

Problem to call with 4634

Hi, I installed patton 4634 with 3cx, on the patton there are 2 isdn point to multipoint, i check the configuration for isdn interface was appropiately for pmp, my problem is:
on call incaming i can receive 4 calls togheter (2 for each isdn line)
in outgoing i can call only 2 calls
I try to change line on the bri, the patton call only on the bri 0/0.
I post the configuration

webserver port 80 language en

system

ic voice 0
low-bitrate-codec g729

system
clock-source 0 0

profile ppp default

profile tone-set default

profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
codec 2 g711ulaw64k rx-length 20 tx-length 20

profile pstn default

profile sip default

profile aaa default
method 1 local
method 2 none

context ip router

interface eth0
ipaddress dhcp
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu

interface eth1
ipaddress 192.168.4.151 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu

context cs switch

interface isdn isdnif0
route call dest-interface sipif0

interface isdn isdnif1
route call dest-interface sipif1

interface sip sipif0
bind gateway sipgw0
service default
route call dest-interface isdnif0
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10000 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri

interface sip sipif1
bind gateway sipgw1
service default
route call dest-interface isdnif1
remote-party-id called-party
address-translation outgoing-call request-uri user-part fix 10001 host-part to-header target-param none
address-translation incoming-call called-e164 request-uri

context cs switch
no shutdown

gateway sip sipgw0
bind interface eth1 router

service default
domain 192.168.4.200
authentication 10000 password 10000 default
default-server 192.168.4.200 loose-router
registrar 192.168.4.200
user 10000

gateway sip sipgw0
no shutdown

gateway sip sipgw1
bind interface eth1 router

service default
domain 192.168.4.200
authentication 10001 password 10001 default
default-server 192.168.4.200 loose-router
registrar 192.168.4.200
user 10001

gateway sip sipgw1
no shutdown

port ethernet 0 0
medium auto
encapsulation ip
bind interface eth0 router
no shutdown

port ethernet 0 1
medium auto
encapsulation ip
bind interface eth1 router
no shutdown

port bri 0 0
clock auto
encapsulation q921

q921
protocol pmp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface isdnif0 switch

port bri 0 0
no shutdown

port bri 0 1
clock auto
encapsulation q921

q921
protocol pmp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side user
encapsulation cc-isdn
bind interface isdnif1 switch

port bri 0 1
no shutdown

port bri 0 2
clock auto
encapsulation q921

q921
protocol pmp
uni-side auto
encapsulation q931

q931
protocol dss1
uni-side net

port bri 0 2
shutdown


I disable the firewall and antivirus on the pc with 3cx. I have only one net card whit only one ipaddress

Can anyone help me?
Thanks

 

[marcovalli]

PATTON 4634 BUSY TONE

I have a Patton 4634 configured as follows:
I have 2 ISDN lines connected on BR0/0 and BR0/1 (line A and line 8)

Line A works correctly both calling and receiving phone calls.

Line B, instead, allows me to call and receive but, when line is engaged and I receive a phone call, the person who is calling doesn’t hear the engaged signal but the free one.

If I exchange the two lines on the PATTON, line B (in this case connected to BR0/0) works correctly, instead line A (connected to BR 0/1) has the same defect (doesn’t give the engaged signal)

 

[rnoguera]

Marcovalli:

If you have 2 BRI, you have 4 voice lines (2 on each BRI) and the "busy" tone should be heard only when you already have 2 calls established in a line...

 

[deangelisg]

yes...is my case

 

[deangelisg]

I solve the problem, for work fine on the 3cx configuration need to create another gateway with same ip of the first but with another port, in this case 5062 that use the patton 4634 with default for second gateway