Have it mostly configured...
initial config *0763 worked same
now x = scrubbed digit
GXW410X
Port 1 = Line 1 > DID *xxx0763
Port 2 = Line 2 > DID *xxx1012
Port 3 = Blank No Line > DID 000002
Port 4 = Line 3 > DID *xxx9683 (FAX)
Its working - except - need to specifically identify Port 4 Only use for Outbound from Ext 150 HT802.
HT802
Port 1 -MFP Copier & Fax > ext 150
Port 2 - Line 1 Old PBX > ext 120
from 3cx Phones dial 120 > all old PBX phones tied to inbound ring group will ring.
phones on old PBX can dial extensions - but expect only 1 old phone at a time would work (really only need 1 to be able to work)
Analog line 1 > Moved from Old PBX Port 1 > GXW410X Port 1
Analog line 2 > Moved from Old PBX Port 2 > GXW410X Port 2
Analog line 3 > Direct to MFP FAX > GXW410X Port 4
DID Inbound -
Line 1 and 2 > tied to Ring Group 802
Line 3 > tied to 888 faxserver
calling line 3 - still rings 802 though...
-----------------------
--- re-checking my inbound DIDs just in case...
Outbound wise - how would I say only allow using Line 1 & Line 2 and don't allow using line 3 in port 4?
is there anyway to block using that 3rd line?
Outbound rules - don't see options to only use DID # / DID # for outbound...
know this is only an oddity for PSTN Gateways but figured I'd ask...
- know the only other option is add another PSTN Gateway and then have separate out bound rules
only allow outbound from Ext X through that gateway... I guess.
initial config *0763 worked same
now x = scrubbed digit
GXW410X
Port 1 = Line 1 > DID *xxx0763
Port 2 = Line 2 > DID *xxx1012
Port 3 = Blank No Line > DID 000002
Port 4 = Line 3 > DID *xxx9683 (FAX)
Its working - except - need to specifically identify Port 4 Only use for Outbound from Ext 150 HT802.
HT802
Port 1 -MFP Copier & Fax > ext 150
Port 2 - Line 1 Old PBX > ext 120
from 3cx Phones dial 120 > all old PBX phones tied to inbound ring group will ring.
phones on old PBX can dial extensions - but expect only 1 old phone at a time would work (really only need 1 to be able to work)
Analog line 1 > Moved from Old PBX Port 1 > GXW410X Port 1
Analog line 2 > Moved from Old PBX Port 2 > GXW410X Port 2
Analog line 3 > Direct to MFP FAX > GXW410X Port 4
DID Inbound -
Line 1 and 2 > tied to Ring Group 802
Line 3 > tied to 888 faxserver
calling line 3 - still rings 802 though...
-----------------------
--- re-checking my inbound DIDs just in case...
Outbound wise - how would I say only allow using Line 1 & Line 2 and don't allow using line 3 in port 4?
is there anyway to block using that 3rd line?
Outbound rules - don't see options to only use DID # / DID # for outbound...
know this is only an oddity for PSTN Gateways but figured I'd ask...
- know the only other option is add another PSTN Gateway and then have separate out bound rules
only allow outbound from Ext X through that gateway... I guess.
