3CX Skype Connect

[spring]

Dear All,

I am using 3CX version 12.5. when setup 3cx skype connect the port trunk status is registered but i could not call out and also there is no in/out information at trunk port when i dial to mobile number.

Thanks for any comments to solve this.

 

[leejor]

The 3CX Server log of a call attempt may shed some light on what is happening. It may be your outbound rules, and what digits are being sent out, if the call is getting that far.

 

[spring]

Thanks Leejor,
I think outbound rule is ok even it is wrong it still show call routing to that port when make dailing.

Another question is to call out from 3CX Skype connect it use skype balance or skype manager balance?

 

[leejor]

I think outbound rule is ok even it is wrong it still show call routing to that port when make dailing.

...and what response is shown in the log when the call is connected to the trunk? Is there a time-out, is the call rejected by Skype?

Another question is to call out from 3CX Skype connect it use skype balance or skype manager balance?

As I don't use the service myself, I can't answer that, but someone else on the forum probably can.

 

[spring]

This is what the logs show

21-Nov-2014 09:57:24.895 Leg L:5.1[Extn] is terminated: Cause: BYE from PBX
21-Nov-2014 09:57:24.894 [CM503020]: Call(C:5): Normal call termination. Call originator: Extn:101. Reason: No answer
21-Nov-2014 09:57:24.894 Leg L:5.2[Line:10000>>85598756999] is terminated: Cause: 408 Request Timeout/INVITE from local
21-Nov-2014 09:57:24.894 L:5.1[Extn] failed to reach Line:10000>>85598756999, reason No Answer
21-Nov-2014 09:57:24.894 Call to T:Line:10000>>85598756999@[Dev:sip:[email protected]:5060] from L:5.1[Extn] failed, cause: Cause: 408 Request Timeout/INVITE from local
21-Nov-2014 09:57:24.894 [CM503003]: Call(C:5): Call to <sip:[email protected]:5060> has failed; Cause: 408 Request Timeout/INVITE from local
21-Nov-2014 09:57:13.182 Currently active calls - 1: [5]
21-Nov-2014 09:56:52.754 [CM503025]: Call(C:5): Calling T:Line:10000>>85598756999@[Dev:sip:[email protected]:5060] for L:5.1[Extn]
21-Nov-2014 09:56:52.705 [CM503027]: Call(C:5): From: Extn:101 ("sophal" <sip:[email protected]:5060>) to T:Line:10000>>85598756999@[Dev:sip:[email protected]:5060]
21-Nov-2014 09:56:52.705 [CM503004]: Call(C:5): Route 1: from L:5.1[Extn] to T:Line:10000>>85598756999@[Dev:sip:[email protected]:5060]
21-Nov-2014 09:56:52.705 Line limit check: Current # of calls for line Lc:10000(@Skype[<sip:[email protected]:5060>]) is 0; limit is 1
21-Nov-2014 09:56:52.705 Call(C:5): Call from Extn:101 to 098756999 matches outbound rule 'Rule for Skype'
21-Nov-2014 09:56:52.704 [CM503001]: Call(C:5): Incoming call from Extn:101 to <sip:[email protected]:5060>
21-Nov-2014 09:13:17.102 [CM504001]: Endpoint Extn:101: new contact is registered. Contact(s): [sip:[email protected]:63271 / 101]

 

[leejor]

21-Nov-2014 09:57:24.894 L:5.1[Extn] failed to reach Line:10000>>85598756999, reason No Answer
21-Nov-2014 09:57:24.894 Call to T:Line:10000>>85598756999@[Dev:sip:[email protected]:5060] from L:5.1[Extn] failed, cause: Cause: 408 Request Timeout/INVITE from local

Are you certain that you are sending the correct number format, and by that I mean including any required prefix? From what I've found, the numbers must be in the International Format.

https://support.skype.com/en/faq/FA10573/what-format-should-my-dial-plan-be-in