Toggle sidebar Toggle sidebar

HELP!!!!!!

Status
Not open for further replies.

crazy-alex

Joined
Sep 1, 2011
Messages
29
Reaction score
0
Im trying the new 2.2.0 rc3 Beta release but i seem ta have a problem when i go to setup the asteris SIP Settings... its telling me that the auto detect has failed so i try setting it manually and its still not working so basically all my external extension are not registering and in turn not working... All my ports are opened as im replacing the old pbx i had located here with the new one... am i the only one having this issue???
 
This is whats happening..... Please help im pulling my hair... :(
 
Hi

You talk about NAT informations?

All seems works from my side. :huh:

into sip_general_additional.conf:
nat=yes
externip=my-public-ip
localnet=193.107.20.0/255.255.255.0

and the values are into asterisk : sip show settings
Code: 
Network Settings:
---------------------------
  SIP address remapping:  Enabled using externaddr
  Externhost:             <none>
  Externaddr:             my-public-ip:0
  Externrefresh:          10
  Localnet:               193.107.20.0/255.255.255.0
 
All working from this side also on 2.2rc3.

No issues with autodetection....

Can you provide any more information about your system??

Did you perform and Freepbx upgrades, any yum upgrades??

Are you running the system behind a router??

Can you ping 8.8.8.8 from the Linux prompt??

Can you ping www.google.com from the Linux prompt??

Regards
Bob
 
danard i set it up manually when the aut dtect failed... i even went as far as to create it manually in the command prompt and still nothing -___-


danardf said:
Hi

You talk about NAT informations?

All seems works from my side. :huh:

into sip_general_additional.conf:
nat=yes
externip=my-public-ip
localnet=193.107.20.0/255.255.255.0

and the values are into asterisk : sip show settings
Code: 
Network Settings:
---------------------------
  SIP address remapping:  Enabled using externaddr
  Externhost:             <none>
  Externaddr:             my-public-ip:0
  Externrefresh:          10
  Localnet:               193.107.20.0/255.255.255.0
Click to expand...
 
im running an i7 mainboard with an i3 processor and a 128 gb SSD

i have not preformed any FreePBX upgrades or yum upgrades

i have a router with all the ports open

it pings 8.8.8.8 perfectly but when i try www.google.com it says unknown host but if i put the ip of www.google.com it pings perfectly

Bob said:
All working from this side also on 2.2rc3.

No issues with autodetection....

Can you provide any more information about your system??

Did you perform and Freepbx upgrades, any yum upgrades??

Are you running the system behind a router??

Can you ping 8.8.8.8 from the Linux prompt??

Can you ping www.google.com from the Linux prompt??

Regards
Bob
Click to expand...
 
ok Danard i got the same thing you got on the asterisk and im still not able to connect from outside... any ideas???
 
For resume!
you can ping to an external ip address - ok!
you cannot ping to an external host name - ok!

It's a DNS issue!!!

Maybe a routing problem, or else.
Try to setting a good DNS server, (internal, or external).
Try to ping them before.

Until your LAN will not be clean you cannot be able to connect any extension from WAN.
 
Thank you Danard i set the DNS and its working excellently now thank you very much for your help


danardf said:
For resume!
you can ping to an external ip address - ok!
you cannot ping to an external host name - ok!

It's a DNS issue!!!

Maybe a routing problem, or else.
Try to setting a good DNS server, (internal, or external).
Try to ping them before.

Until your LAN will not be clean you cannot be able to connect any extension from WAN.
Click to expand...
 
ok

Great, i'm happy for you. :)

Regards
 
I have a question about this same system i hooked up the lines through a PRI card and i can dial out the only thing that isnt working is when you call in its telling me the number isnt in service what can i do to correct this???


danardf said:
ok

Great, i'm happy for you. :)

Regards
Click to expand...
 
You need to paste the CLI output (asterisk -r) when receiving a call, to see what is going on...
 
local*CLI>
Verbosity is at least 3

local*CLI>
 -- Starting simple switch on 'DAHDI/1-1'

local*CLI>
 -- Executing [s@from-pstn:1] NoOp("DAHDI/1-1", "No DID or CID Match") in new stack
-- Executing [s@from-pstn:2] Answer("DAHDI/1-1", "") in new stack

local*CLI>
 -- Executing [s@from-pstn:3] Wait("DAHDI/1-1", "2") in new stack

local*CLI>
 -- Executing [s@from-pstn:4] Playback("DAHDI/1-1", "ss-noservice") in new stack

local*CLI>
 -- <DAHDI/1-1> Playing 'ss-noservice.gsm' (language 'en')

local*CLI>
 -- Executing [s@from-pstn:5] SayAlpha("DAHDI/1-1", "") in new stack
-- Executing [s@from-pstn:6] Hangup("DAHDI/1-1", "") in new stack
== Spawn extension (from-pstn, s, 6) exited non-zero on 'DAHDI/1-1'
-- Executing [h@from-pstn:1] Macro("DAHDI/1-1", "hangupcall,") in new stack

local*CLI>
 -- Executing [s@macro-hangupcall:1] GotoIf("DAHDI/1-1", "1?endmixmoncheck") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,9)

local*CLI>
 -- Executing [s@macro-hangupcall:9] NoOp("DAHDI/1-1", "End of MIXMON check") in new stack

local*CLI>
 -- Executing [s@macro-hangupcall:10] GotoIf("DAHDI/1-1", "1?nomeetmemon") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,15)
-- Executing [s@macro-hangupcall:15] NoOp("DAHDI/1-1", "MEETME_RECORDINGFILE=") in new stack

local*CLI>
 -- Executing [s@macro-hangupcall:16] GotoIf("DAHDI/1-1", "1?noautomon") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,18)

local*CLI>
 -- Executing [s@macro-hangupcall:18] NoOp("DAHDI/1-1", "TOUCH_MONITOR_OUTPUT=") in new stack
-- Executing [s@macro-hangupcall:19] GotoIf("DAHDI/1-1", "1?noautomon2") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,25)

local*CLI>
 -- Executing [s@macro-hangupcall:25] NoOp("DAHDI/1-1", "MONITOR_FILENAME=") in new stack

local*CLI>
 -- Executing [s@macro-hangupcall:26] GotoIf("DAHDI/1-1", "1?skiprg") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,29)

local*CLI>
 -- Executing [s@macro-hangupcall:29] GotoIf("DAHDI/1-1", "1?skipblkvm") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,32)

local*CLI>
 -- Executing [s@macro-hangupcall:32] GotoIf("DAHDI/1-1", "1?theend") in new stack

local*CLI>
 -- Goto (macro-hangupcall,s,34)

local*CLI>
 -- Executing [s@macro-hangupcall:34] Hangup("DAHDI/1-1", "") in new stack

local*CLI>
 == Spawn extension (macro-hangupcall, s, 34) exited non-zero on 'DAHDI/1-1' in macro 'hangupcall'

local*CLI>
 == Spawn extension (from-pstn, h, 1) exited non-zero on 'DAHDI/1-1'

local*CLI>
 -- Hanging up on 'DAHDI/1-1'

local*CLI>
 -- Hungup 'DAHDI/1-1'

local*CLI>

jgutierrez said:
You need to paste the CLI output (asterisk -r) when receiving a call, to see what is going on...
Click to expand...
 
OK i figured it out i was a problem wityh my inbound routes i set one up with no specified DID or CID and its working perfect :) thank you guys
 
Status
Not open for further replies.

Latest Posts

Members Online Now

Total: 457 (members: 10, guests: 447)

Forum statistics

Threads
111,865
Messages
589,461
Members
164,704
Latest member
cdl1
3CX Logo Footer Copyright © Sitemap Privacy
Top Bottom