WHY it is no work corectly???

[paul-cdma]

17:52:23.359 StratInOut:nHangUp [CM104007] Call(58): Call from Ln:10001@dlink 6004s to 999 has been terminated by Ln:10001@dlink 6004s; cause: BYE; from IP:217.30.245.110
17:52:19.421 CallLegImpl:nConnected [CM103001] Call(58): Created audio channel for Ln:10001@dlink 6004s (217.30.245.110:9002) with Media Server (217.30.245.111:7116)
17:52:16.781 CallConf:nProvisional [CM103003] Call(58): Ext.500 is ringing
17:52:16.546 CallConf:nIncoming [CM103002] Call(58): Incoming call from 10001 (Ln:10001@dlink 6004s) to sip:[email protected]

I use dlink fxo gateway and call for 8432505999. why 3cx divert call for ext500?

 

[DaKhalli]

you should provide more information, but you can try the following:

check your dial rules. the r in the transform mask removes the first digit dialed.

also check the gateway configuration if its registered properly and the phone too.

 

[paul-cdma]

rule is three for digit 0 - to dlink gateway, for digit 2 and 3 into same dlink. dllink is registered properly, I can call to line connected to dlink interface correctly, but if i call to line into dlink and it`s trans my call and dialed number into 3cx ( 8432505999...) and why it transfer this call into 500?

 

[paul-cdma]

[CM104007] Call(2): Call from Ln:10001@dlink 6004s to 500 has been terminated by Ln:10001@dlink 6004s; cause: CANCEL; from IP:217.30.245.110

18:15:55.203 CallConf:nProvisional [CM103003] Call(2): Ext.500 is ringing

18:15:54.968 CallConf:nIncoming [CM103002] Call(2): Incoming call from 10001 (Ln:10001@dlink 6004s) to sip:[email protected]

why? it is dont see number 2505999 and transfer call to ext 500

 

[paul-cdma]

the route conf for internal call for this device is route for exten 500... but why it`s dont analizy number what i deal in

 

[DaKhalli]

what does you outbound rule say? you still have the default rule in there?

If so, remove the "r" in the transform mask. hope it helps

 

[paul-cdma]

 

[DaKhalli]

checking just a sec

 

[DaKhalli]

I think you have to play with the gateway is external settings for a bit.

But to get it straight:

Outgoing calls work?
Incomming calls work?

Incomming calls display wrong number?
Or number you dial out gets transformed?

 

[paul-cdma]

no! I can call from ext 500 ( softphone) to any ( this is corect) but if i call for line into dlink and it transf this call to 3cx... any dealed number was transfered to ext 500. fo example i call to fxo line ( like pstn call) hear voice promt to deal number... then dial 2505999. dlink place sip call to 3cx and 3cx was transfer this call for ext.500 in anytime or any dealed number

 

[DaKhalli]

Changed above msg, please check again

All looks ok on your server tho. But maybe i have to make an extension for myself and see what happens?

What country are you in?

 

[DaKhalli]

also you can play around with editing the "other settings" of the voip gateway, specially the

caller id
called number settings.

 

[paul-cdma]

I am from russia please you can do ext for yourself and try

 

[DaKhalli]

also play around with extension is external setting in the extension settings, provide the softphone also with a stun-server adress to take away any NAT related problems.

 

[paul-cdma]

there is no NAT problem be cause i use only ext ip adress

 

[DaKhalli]

ok created an extension, gotta eat now be back in 30 mins ill look into it some more.

 

[paul-cdma]

OK i find a solution. the problem is in default gateway and dialed number plan in 3cx. Thank`you All

 

[DaKhalli]

no problem mate glad you got it solved