X-Lite one way Voice

[todd]

3CX Phone System Version3.0.2328.0 (Free Version)

Extension 8007
Extension is external
Bind to Media Server
X-Lite V3.0

Extension 8000
Extension is Internal
Bind to Media Server
SPA2000


When make call from 8007 to 8000, just 8000 can hear voice from 8007. No voice from 8007 to 8000.
But, If I change X-Lite V3.0 to a SPA200 them working fine. OR when I setup a Internal extension use X-Lite, it work fine. So, I think my server setup is good but only X-Lite V3.0 for Extension is external with some problem. Or maybe the ports problem?


Any suggestions for this? Thanks!!!


21:02:45.625 StratLink:nHangUp [CM104001] Call(22): Ext.8000 hung up call; cause: BYE; from IP:192.168.1.103
21:02:28.328 CallLegImpl:nConnected [CM103001] Call(22): Created audio channel for Ext.8000 (192.168.1.103:16480) with Media Server (192.168.1.2:7054)
21:02:28.328 StratInOut:nConnected [CM104005] Call(22): Setup completed for call from Ext.8007 to Ext.8000
21:02:28.328 CallLegImpl:nConnected [CM103001] Call(22): Created audio channel for Ext.8007 (192.168.0.103:50582) with Media Server (60.241.xxx.xxx:9016)
21:02:26.937 CallConf:nProvisional [CM103003] Call(22): Ext.8000 is ringing
21:02:26.843 CallConf:nIncoming [CM103002] Call(22): Incoming call from 8007 (Ext.8007) to sip:[email protected]:5060

 

[SY]

Created audio channel for Ext.8007 (192.168.0.103:50582) with Media Server (60.241.xxx.xxx:9016)

Address specified by external extension 80007 is not global. Configure X-lite (external) to "Discover Global Address".

 

[DaKhalli]

try adding a stun server to the xlite account.

that solved my audio problems with xlite.

 

[todd]

working now!!!Thanks!!!
I set a stun server to the xlite account.
23:32:47.906 StratLink:nHangUp [CM104001] Call(36): Ext.8000 hung up call; cause: BYE; from IP:192.168.1.103
23:32:39.359 CallLegImpl:nConnected [CM103001] Call(36): Created audio channel for Ext.8007 (218.215.xxx.51:59329) with Media Server (60.241.xxx.xxx:9040)
23:32:39.343 StratInOut:nConnected [CM104005] Call(36): Setup completed for call from Ext.8000 to Ext.8007
23:32:39.343 CallLegImpl:nConnected [CM103001] Call(36): Created audio channel for Ext.8000 (192.168.1.103:16406) with Media Server (192.168.1.2:7080)
23:32:37.890 CallConf:nProvisional [CM103003] Call(36): Ext.8007 is ringing
23:32:36.859 CallConf:nIncoming [CM103002] Call(36): Incoming call from 8000 (Ext.8000) to sip:[email protected]

 

[DaKhalli]

cool mate glad i could help out

 

[ksantella]

same issue

cant seem to get the external xlite to give audio in both directions.

I can connect and resolve to my pbx from xlite (external). I hear audio on my laptop but not inbound to my sip phone inside.

I have tried with and without the stun server with same results. The xlite is on a sprint broadband cellular card no router.

any ideas?

 

[DaKhalli]

and the router on the server side?

 

[ksantella]

router on server

port forwards on router. PBX attached as well as Linksys 942's to this router.

1 VOIP-TFTP 69 69 192.168.1.2
2 VOIP-SIP 5060 5061 192.168.1.2
3 VOIP-RTP 8000 9998 192.168.1.2
4 PBX 5480 5482 192.168.1.2
5 VOIP-STUN 3478 3478 192.168.1.2
6 VOIP-INTERNAL 7000 7500 192.168.1.2
7 VOIP_VOICE 10000 20000 192.168.1.2

 

[Anonymous]

You also need 9000 - 9003

Is you XLite configured as an extension?

 

[ksantella]

xlite extension

It is set up as an external extension (201) and I do have ports 9000-9003 open. If you look at the previous post you will see ports 8000-9998 open.

all comm works fine with normal inbound calling. It is only when the extension is outside of the pbx that the audio is not being transmitted in the one direction.