Search results

  1. 3cx 15.5 no provisioning

    Thank you everyone, I restored the configs from my 12.5 backup placed it in the tftp path and the yealinks work.

  2. 3cx 15.5 no provisioning

    We have a mixed environment of phones. Yealink T46G, Polycom IP6000 and Cisco 7940's. We use Vlans, DHCP options and TFTP to pass config to phones. we upgraded from 12.5 to 15.5. In 12.5 - 3cx would generate the config file and place it in c:\programData\ 3cx......provisioning\wfu3g0ga2x\ after...

  3. 3cx 15.5 no provisioning

  4. 3cx 15.5 no provisioning

    Thank you , i tried this. and i see in tftp server where the phone tries to retrieve file and it fails because file does not exist.

  5. 3cx 15.5 no provisioning

    I am trying to manually provision a yealink T46G on 3cx 15.5. I am able to add the phone under an extension but the config file is never generated nor do i see a download of any kind. I read that its a http request but to where and when. I have checked the TFTP path and crossed reference with...

  6. 3CX Self assigned certificate needed for version 15 install

    if you want to create your own SSL for an internal server here is how.

  7. 15v - call logs retention

    i want to keep call logs for reporting for more then 12 months. where is this setting??? Thank you in advance.

  8. Patton gateway config file generator - doesn't put gateway into config

    its been like that since version 12.5. we get the same results on 14 and 15sp5.

  9. Presence

    Presence over a bridge(WAN) from 12.5 to 15 does not work. users on 12.5 cannot see users on the 15 system. Pretty disappointing for someone with 14 locations and over 1000 users.

  10. Where is Add CID Rule

    Yes i tried this under Inbound Rules: "Inbound Rule Type" Caller ID Number/mask . For anyone else looking for this. this works but the rule needs to be above all your DID rules. Thank you

  11. Where is Add CID Rule

    I am looking for the Add CID Rule for Inbound Rules - Routing incoming calls. It is described here: http://www.3cx.com/docs/manual/inbound- ... vorfngfl2b “Add CID Rule.” I have looked on both version 12.5 PRO and 14 SP3 PRO and can not locate it. I am trying to route calls based on Caller ID...

  12. Recover accidental Reject of Phone on the Sever Manager > Phones page

    Have you checked the black listed ip tab under security ?

  13. patton 4970 and more then one 3cx server

    There is a bridge between A and B. But I don't want to use bridges because I don't want every call from location B to C to have to route through location A. All these locations are connected via a WAN.

  14. patton 4970 and more then one 3cx server

    has anyone configured more then one 3cx server located in different cities to a single Patton 4970 t1\e1. Location A- 3cx ---\ ........................... <---> Patton 1 is located -C (Mitel System) connected to a Mitel system via T1\E1 port Location B - 3cx---/ how do you configure the...

  15. Policy or outbound rule for internal numbers

    leejor are you apply this on the Patton device?

  16. Policy or outbound rule for internal numbers

    the loop back would be great if we can use a wildcard. i am going to try the block method. force these users to use 4 digits. :D

  17. Policy or outbound rule for internal numbers

    we have DIDs for all users. example 1-312-555-6001 = Smith - extension 6001 the Telecom providers only sends last 4 digits over PRI\ISDN -- *6001 is the inbound rule. here is my scenario :O dont ask why users dont use 4 digits ??$%$!! some users dial internal people using the 11...

  18. [Resolved]This Call cannot completed, please try again later

    Re: [Resolved]This Call cannot completed, please try again l I was receiving the same error. After the 3cx install i went into IIS to bind the site to a specific IP address. 3cx does not like this change and VM stopped working. I later went back and changed to "all unassigned" and VM is...
3CX Logo Footer Copyright © Sitemap Privacy
Top Bottom